国产高清晰在线播放-国产高清亚-国产高清亚洲-国产高清亚洲免费片-国产高清一-国产高清一区

Welcome to the official website of Xingtai Degang Electronics Co., Ltd!
邢臺德港電子有限公司
keywords:
news information INDEX > news information > News Center > How to detect the phenomenon of inaccurate weighing of electronic loadometer?

How to detect the phenomenon of inaccurate weighing of electronic loadometer?

Time:2020.12.03     News sources: Hebei Chaoda Sealing Products Co., Ltd

Traditional detection methods:

1. Partial load detection

In the international recommendation R76 "Non-Automatic weighing apparatus" and JJG555-96 "General Verification Regulations for Non-automatic weighing apparatus"

The loadometer partial load detection is based on "the number of bearing points to determine the amount of weight applied; And Jordan farmar to

Apply to the position above each support point, taking care not to form unnecessary stacking in the placement area if used singly

The weights can be put in the center; If multiple small weights are used, distribute them evenly throughout the area.

This method can achieve the purpose of adjusting the loadometer's off-loading. It is a guarantee bar for mechanical weights

The consistency of the bar - to - force ratio ensures the consistency of the output voltage signal of the weighing sensor for the electronic weigher.

2. Weighing detection

The traditional weighing test method is to start with no load, apply the test load gradually, and then step by step in the opposite order

Unload the test load to zero. If the platform is composed of three loaders, the recommended method is as follows:

(1) Method of weighing rolling load

When the conditions are suitable, rolling loads should be used to test the off-loading of the loadometer. As the current track scale deviation

The loading test method is the same. The method is: at different positions of the starting, middle and end of the load carrier, the load is not greater than

0.8 times the scale, equivalent to the commonly used centralized rolling measurement load. The rolling load is used to test the off-loading of the loadometer.

You can kill two birds with one stone. Firstly, it can make the output voltage signal size of the weighing sensor consistent; Second, it can simulate

The stiffness of the load carrier in actual use.

(2) Detect the weighing according to the centralized loading method

According to the traditional method of detection and weighing, all the 100t weights of * weigher were placed at 18m long, 3.4m wide, and the dead weight was

When the three-stage bearing platform at 15.84t is used, the average load q per unit length is 64.36kg/cm, and the deformation of the bearing platform is

0.26 cm. In this way, the electronic weighter composed of three stages of the carrier, the weight of the scale, are added to one of the

On the area of the section, the effect is close to that of the two axes acting on the central part of the load carrier at 32t, respectively. The question is, if you want to follow

If the weighing load is applied to the three stages respectively, the workload will increase twice.

 

≡  contacts:Manager Wang ≡  mobile:13930926376 ≡  Telephone:0319-2158243 ≡  fax:0319-2159641 ≡  address:No. 1 in Rongtai science and Technology Incubation Park, south of Xingda street, Xingtai Economic Development Zone
河北超達密封
版權所有:邢臺德港電子有限公司       網站備案/許可證號:       

冀公網安備 13050902000085號

技術支持:邢臺市網商軟件開發有限公司
主站蜘蛛池模板: 成人精品aaa | 成人乱码 | 福利社影院 | 精品国产一区二区三 | 七七影院 | 日本色免费一区二区 | 国产一区福利 | 青青草极品视觉盛 | 91国产精品一区 | 国产综合同事 | 国产在线观看第二页 | 日韩系列免费精品 | 九九视频| 96好影院| 成人日韩在线观 | 国产尤物一区二 | 国产捆绑专区 | 日韩系列第一页 | 精品a在线观看 | 欧美另类激情 | 另类小说自拍 | 日本成人卡一 | 国产精品玖玖玖 | 国产又黄又爽 | 日本动漫瀑 | 91拍拍在线观看 | 日本乱理 | 国产精品亚洲 | 人成在线v网站 | 国产熟女一 | 日韩精品视频老牛 | 午夜电影一区 | 日本一区二区高清 | 拍国内精品老妇 | 国产精品巨作无遮拦 | www在线黄 | 日本国产精品二区 | 日本免费一区二区 | 丝袜图片 | 91精品手 | 日本中文字幕免 |